Steel & workshop materials
Cone Flat Pattern Calculator: Reducer Development
This calculator develops the flat pattern of a cone frustum, used for concentric reducers, hoppers, chimney transitions and funnels. Enter the large and small diameter, the vertical height and the plate thickness, and it gives the outer and inner pattern radii, the sector angle, the chord, the arc lengths and a table of set-out coordinates. It draws the pattern and exports a DXF for plasma or laser cutting.
- Free, no sign-up
- Runs in your browser
- Built for Islamabad & Rawalpindi
This free calculator runs in your browser and needs JavaScript. If it does not load, call or WhatsApp us on +92 304 2435577 and we will do the calculation for you.
Cones are developed on the mean diameter, the centreline of the plate. Using the outside diameter makes the cone slightly too big once rolled, a difference that matters on thick plate.
What This Tool Does
It converts outside or inside diameters to mean diameters, can split the pattern into several pieces for smaller sheets, and gives coordinates so the pattern can be marked out without a long trammel.
Who It Is For
- Fabricators making reducers, hoppers and ducts.
- Plasma and laser operators.
- Students learning pattern development.
How To Use It
- Enter both diameters, the height and thickness.
- Say whether the diameters are outside, mean or inside.
- Choose how many pieces.
- Click Develop pattern and download the DXF.
How The Calculation Works
Slant L = √(h² + (R − r)²) on mean radii R and r. Outer pattern radius = L × R ÷ (R − r), inner radius = outer − L. Sector angle = 360° × R ÷ outer pattern radius.
Worked Example
600 / 300 mm outside, 400 mm high, 6 mm plate.
| Input or result | Value |
|---|---|
| Mean diameters | 594 / 294 mm |
| Slant | 427.2 mm |
| Pattern radii | 845.9 and 418.7 mm |
| Sector angle | 126.4° |
The outer arc equals π × 594 = 1,866 mm, which checks the pattern.
Features And Benefits
- Mean-diameter correction.
- Split patterns.
- Coordinates and DXF.
Assumptions And Accuracy Limits
- Concentric (straight) cones only; offset cones and square-to-round transitions need triangulation.
- Seam allowance is not added.
Common Mistakes To Avoid
- Developing on outside diameter. Use the mean diameter.
- Using slant height as vertical height. They differ.
- No trial piece. Check a thin template before cutting thick plate.
Cone Fabrication In Islamabad And Rawalpindi
Hoppers for feed mills and crushers, chimney reducers and water tank outlets are common cone jobs in the twin cities. Ramzan Steel Works cuts, rolls and welds cones and reducers to drawing.
Frequently Asked Questions
How do you calculate a cone flat pattern?
Find the slant height, then the pattern radius = slant × large radius ÷ (large radius − small radius), and the angle = 360° × large radius ÷ pattern radius.
Should I use inside or outside diameter?
Develop on the mean diameter, which is the outside diameter minus the thickness.
Can I make a cone in two halves?
Yes. Split the angle into two equal sectors and weld two seams.
Related Free Tools
- Pipe Miter, Elbow & Branch Saddle Template CalculatorGet cut angles, marking ordinates and a true-size SVG wrap template for pipe elbows and branch saddles.
- Sheet Metal Bend Allowance & Flat Pattern CalculatorBend allowance, bend deduction, setback and flat blank length with bend lines, from T, R, angle and K-factor.
- All-in-One Steel, Iron, SS & Aluminium Weight EngineTheoretical weight for pipe, square tube, angle, channel, bar, plate and more — any material, any unit.
- Steel Sheet & Plate Cutting OptimizerNest rectangular pieces onto sheets with kerf and margins, and see sheets needed and waste.
Get A Measured Quotation
Ramzan Steel Works fabricates cones, hoppers and reducers in Islamabad and Rawalpindi.
